Search results

Hi, I am trying to use a motor for a project. As it didn't spin at the beginning within an assembly, I used a multimeter to measure the resistance. When I set it to X1 scale and connected the multimeter probes, the motor started to spin. When I set the resistance to a X10 scale, I got a stable...

Hi, I am trying to find out the usage of RFA030. I pluggged in the URF module to the PC, and installed the URF driver successfully. Then I assembled the ERF module to the Microbot. When I started the Picaxe Editor, it was able to detect the URF module. However, when I tried to download a...

Hi, I am looking at the RFA030 and like to confirm the following : (a) it can be a substitute for the AXE027. If this is the case, the URF module is attached to the PC and the ERF module may be attached to a picaxe microntroller (?) (b) Is the ERF designed to allow it to attach to a Microbot ...

Hi, I am referring to the Tune Command in 'A guide to using flowcharts within PICAXE Editor 6'. My screenshot in PE6 for the Tune Command was different from that shown on page 14. The one on page 14 did not prompt with a first line "Please paste tune below this line....". At the same time...

Hi, I assembled a line tracker at C.2. Is it still possible for me to assemble SRF005 at the same pin but on top of the line tracker, yet : (a) have a program that can drive both the line tracker and the SRF005 ? (b) have no connection issues electrically and mechanically ?

Hi, I am trying to find out the assembly status of the datalogger when purchased. Is self assembly required or it has been preassembled ? On the AXE110P manual first page, it says that the product is available preassembled. However in section 2 of the same manual, there are instructions for self...

Hi, I am looking through the products AXE171 and SPE035. I have 2 questions : (a) are there plans to release assembled versions of these 2 modules ? (b) the connections from the modules to the microbot should be done via pinC.2 right ? If this is the case, and I have a line tracker module...

Hi, I read the bot120 manual and on page 28, a line tracker program was introduced (reading reflected light). Given that we are not trying to have the line tracker roam around at this stage, am I supposed to see some visible output once the program is downloaded ? e.g. navigating from picaxe...

Hi, I attempted to use codes for motors. Only 1 motor (B) moved while the other motor (A) did not. I checked the manual, applied a little extra grease to the gearbox of motor A, checked that there were no clearance issues between the Microbot and the wheels, but motor A still did not respond...

Hi, I have been writing programs on LEDs, and push switch, and downloading them smoothly to the Microbot. By the time I wrote the bumper program and tried the download, I had an error as shown in the picture. I saved the file, then tried to : (a) switch off the Microbot and switch on again...

Hi, I refer to page 4 of the AXE027 manual where a programming editor interface was shown. The instructions were to click a 'Refresh' Button, select a port and click ok. When I started Picaxe Editor 6, the interface was different. The main menu was the one I saw in the following picture ...

Hi, on page 4 of the AXE027 manual, there was mention on the possibility of an unsuitable COM port assigned (e.g. COM20). What is the criteria for an unsuitable COM port being assigned ? In the the top most diagram on the right of the same page, only COM1 to COM10 were listed. Assuming Step 1 of...

Hi, I am trying to install the drivers for AXE027 on my windows system. Step 1 of page 2 in the AXE027 manual shows a screen on 'Welcome to the Found New Hardware Wizard' after the AXE027 is plugged. However, the screen I obtained was as below : Please advise if I should click 'Update Driver'...

Hi, is there a recommended number of nuts and bolts that we should attach from the bumper assembly to the motherboard ? I asked because I tried with 2 nuts and 2 bolts (1 set of but and bolt near to each bumper board) and it appears 'ok' at the moment. From the number of points available, it...

Hi, I am referring to the line tracker module. On page 11, there is a picture of the module, and it says "Ensure the Line Tracker module is the correct way up and fit one of the brics to the top of circuit board." The board in the manual didn't have the same look from the one I received...

Hi, My question concerns how the servo board should be assembled to the rear of the microbot. There are 2 sides of the servo board the side with the word 'servo' labelled and the side without the word 'servo' labelled Which side should face up during assembly, or does it matter ? and why ?

Hi, I compared the servo diagram on page 42 of 51 in the bot120 manual (picture 1 as follows): with what was in the set (picture 2 as follows) : The pictures for the servos are different. Can someone help to confirm that the actual servo module is the one I boxed up with dotted lines in...

Hi, I am new to Microbot and have recently purchased a bot120. I am trying to confirm if during the assembly process, I have to detach the board that has the part number BOT120 separated from the pieces labelled 'SRF005', 'SERVO', 'PEN', 'LINE TRACKER' and the bumper boards before I start the...