Information
PICAXE Store
Cloud Programming
Menu
Home
Forums
New posts
Search forums
What's new
New posts
Latest activity
PICAXE
BASIC Commands
PICAXE manuals
PICAXE Editor software
AXE027 USB Cable Drivers
Buy Now
Log in
Register
What's new
Search
Search
Search titles only
By:
Latest activity
Register
Menu
Log in
Register
Home
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
AllyCat's latest activity
A
AllyCat
replied to the thread
SSD1306 Adjust Brightness?
.
Hi, The OP (ZanderPIC) didn't ever indicate if he got his Brightness control working, but the instructions in this thread don't seem...
Yesterday at 8:08 PM
A
AllyCat
replied to the thread
SSD1306 Adjust Brightness?
.
Hi, Here's an "update" which I've just noticed on the Pi Hut site. I've no idea when it was first introduced: The Blockly code for...
Yesterday at 4:15 PM
A
AllyCat
replied to the thread
Picaxe 18m2 to a 128 x 64 oled
.
Hi, I was searching the forum for a "definitive" initialisation routine for the SSD1306 chips, but couldn't find one (however, post #1...
Yesterday at 1:35 PM
A
AllyCat
replied to the thread
Is PE5 (finally) Dead ?
.
Hi, Success! After re-reading Phil's post, I tried right-clicking a .BAS program in File Explorer, selected "Open With" and navigated...
Wednesday at 10:35 PM
A
AllyCat
replied to the thread
Is PE5 (finally) Dead ?
.
Hi, Thanks Jack, that at least solves a problem (for now), should I need to reinstall PE5 again. Thanks Phil. Hmm, I'm rather rusty...
Wednesday at 9:56 PM
A
AllyCat
posted the thread
Is PE5 (finally) Dead ?
in
Active PICAXE Forum
.
Hi, Personally, I still use Program Editor 5 quite often (and don't believe I'm alone). It's particularly useful to quickly read other...
Wednesday at 4:43 PM
A
AllyCat
replied to the thread
Picaxe 18m2 to a 128 x 64 oled
.
Hi, That was possibly in the thread HERE which was primarily intended to document (all of) the Setup and "Default" parameters for the...
Wednesday at 3:54 PM
A
AllyCat
replied to the thread
Picaxe 18m2 to a 128 x 64 oled
.
Hi, Thanks @kjfl, it looks as if OLDmarty nearly has it running correctly. The issue is probably that my code was written for the 128...
Wednesday at 10:00 AM
A
AllyCat
replied to the thread
Picaxe 18m2 to a 128 x 64 oled
.
Hi, Conversion from an M2 series PICaxe to X2 is not always "trivial", for example because the X2's default clock frequency is twice as...
Tuesday at 3:06 PM
A
AllyCat
reacted to
Flenser's post
in the thread
[RESOLU] PICAXE Syntax - First Use
with
Like
.
ASCO, I haven't ever heard of this PICBASIC-3M module before. If I have found the right one then they are manufactured by the Korean...
May 25, 2024
A
AllyCat
replied to the thread
08M2 initial state of I/O pins
.
Hi, To us, "Dead Bug" assembly was a literal and legitimate prototype assembly method (in the late '60s). The (DIL) Integrated...
May 25, 2024
A
AllyCat
replied to the thread
[RESOLU] PICAXE Syntax - First Use
.
Hi, Welcome to the forum. Note that you MUST use a "genuine" PICaxe (presumably now the 28-pin PICAXE-28X2) which is pre-programmed...
May 24, 2024
A
AllyCat
replied to the thread
Frequency to voltage conversion
.
Hi, What do you plan to do with the "analogue voltage" when you've generated it? Most displays and storage devices are (now) likely to...
May 23, 2024
A
AllyCat
replied to the thread
08M2 initial state of I/O pins
.
Hi, Pin C.0 is a default-Low Output from power-up and C.5 requires a pull-down resistor anyway (which the program can pull High with...
May 22, 2024
A
AllyCat
replied to the thread
Advice required re Bipolar Stepper motors
.
Hi, Yes indeed, both the L298N(s) and the Stepper Motors themselves might get VERY Hot. :( The L298N is now a very "old" bipolar...
May 16, 2024
Home
Top