i already googled/searched picaxeforum for
"picaxe math round", "picaxe rounding" etc.
but did not succeed in finding a hint yet.
------------------------------------------------------
ROUNDING NUMBERS, DIGITS BEHIND COMA?
how may i
- use digits for numbers < 1 (such as 0.059)
within...
--------------------------------------------------------------------
control 2 Hitec HS-422 Servos
I would like to control 2 Hitec HS-422 Servos
using a (diy*-)AXE024 (for 08M2) board
*based on the schematics from the manual -
i need several copies and would like to test them
on my...
working on my macbook pro (osx 10.6.8)
with macaxepad & 08MX2 chip connected
i keep getting "hardware not connected" errors
... eventhough
- i succeeded loading a program before
(after numberous tries without really knowing why it worked once)
- this program runs/responds within macaxepad's...
------------------------------------------------------------
SOLDERING ALTERNATIVES
- CONDUCTIVE GLUE/SOLDERING PASTE ... ?
i am looking for a reliable, not-too-expensive alternative
for soldering connections
& found conductive glue/paste products as listed in the following;
....
i assume...
@dippy -
thanks ...
i had a 2nd look and found the information as in the following
... but i am not sure, if these specifications apply to
a conversion from 6V to 5V (?)
-----------------------------------------------
MIC39100
" ....
Input Capacitor
...
when device > 4 inches away from bulk...
i knew i was too enthusiastic
since i forgot about my extremely limited skills/knowledge;
i googled / had a look at the links at farnell/rscomponents' dataheets ...
(please see excerpts within the screenshot attached )
... and could not figure out
what capacitors/resistors i need to add
to...
how may i get a constant power supply of 4.5 Volt
using batteries?
--------------------------------------------------------------
WHAT I FOUND SO FAR
googling and visiting several discussion groups
i found related advice ...
- e.g. using 1 more than the required batteries
in combination with...
I hope you may give me advice on the following subject:
----------------------------------------------------------------
REPLACING PICAXE PROGRAMMER CABLE ?
I tried to replace the PICAXE 027 USB/serial cable
with the TTL-232R-PCB module by "ftdichip"
for
a project that needs a permanent...
-----------------------------------------------------------------------------------------------
i am looking for advice for ...
an antenna
- in combination with a rf amplifier if necessary -
for ...
... for wireless rf data connections
using a 433 MHZ transmitter/receiver
able to transmit...
can i monitor a picaxe's 08m2 circuit's batteries power
using code ?
i wonder if there is any way to use code
in order to check the current state of the batteries' power
providing voltage to a 08m2 controlled circuit
within regular intervals (e.g. every hour).
i tried ...
-------------...
--------------------------------------------------------------------------------------------------
I am working on a simple project that plays
a (downloaded ringtone) rtttl sound file
... the melody's volume should be loud enough
for a "doorbell-like" alert whereas the sound quality
should...
I connected a 08m Proto board to my mac, ....
---> 01
.... installed the software for the usb cable/macaxepad which worked fine ....
---> 02
.... until i tried to check the connection (via terminal, "program", firmware ...)
---> 03a
.... assuming that i might be my lack of soldering skills...
i try to create rtttl files but do not succeed ...
any hint is highly appreciated!
------------------------------------------------------------------------------
MY TRIES TO CREATE RTTTL FILES
via
picaxe's macaxepad's "ringtone wizard"
using .aiff, .wav, .mp3 files
resulted in ...
error...
am a newbee working with mac soft- and hardware
& i spent a a lot of time looking for the following:
------------------------------------
i would like to ...
- transfer in- output data from simple components
(such as a IR LED used for light/dark detection )
- .... via picaxe
- ... to...